I also noticed that when it does this, that the REVERSE light … Then the reverse light goes out and all is right, speed picks back up and it runs good. I have changed the bulb and when i did that the light stayed off until i applied the brakes. My reverse light stays on all of the time as well, but never affected the engine. I have a 2006 Rhino 660 and the red reverse light on the dash panel lights solid red when in reverse gear like it it supposed to.
It doesn't dim or anything when i apply the brakes. What is wrong with 660 grizzly when reverse light you blinking? 01' does not have a reverse rev limit.
I think my problem is the reverse switch. I don't know if the shift linkage just needs adjusted or if there is a faulty sensor. Page 21: Indicator Lights And Warning Light If the warning light stays on, allow the engine to 1. Put a new stator , ignition coil , reg/rec and starter relay still no spark. One of these that we encounter on a regular basis is the reverse sensor below the airbox. I just had it happen today. I purchased it used and it was literally ridden hard and put away wet. If the warning light stays on when the engine 2. I do not have the rev limiter bypassed at this time. Subject: Rhino cutting off at 32-34 mph. Yamaha placed the reverse sensor on your dash and it t While Yamaha has been praised for starting the UTV craze with the Rhino 660 they did make a few mistakes. When I put it in foward gear and start moving foward I will go about 200 feet and the red reverse starts blinking on and off as I drive foward. Yamaha Neutral Switch Assembly (reverse Switch on Some Models) (3GD-82540-11-00) is used in Electrical 1 assembly for 2000 Yamaha Kodiak 4WD (YFM400FAM), Electrical 1 assembly for 2001 Yamaha WARRIOR (YFM350XN), Electrical 1 assembly for 2000 Yamaha WARRIOR (YFM350XM), Front Differential assembly for 2009 Yamaha Wolverine 450 4WD 3C2G (YFM45FXYL) and Electrical … ... Hello forum , I am new here , I have a 2002 660 raptor with no spark . Hi all I am new here this is my first post. The reverse light comes on constantly while in forward gear causing the engine to pop and sputter and lose power, we have changed the micro chip, changed out the gear shift mechanism and the problem still exisits, this all …
First the speedo read zero and was stuck there, then not long after the reverse light started flashing. Oil temperature warning light “ ” circuit. i put the original bulb back in and same thing. Neutral indicator light “N” cool. Went though some real deep water quit a long distance. When in high range forward it will go about 8-11 mph and start sputtering.It is not the CDI box,I found out the hard way by buying one).Any help would be great before I light the whole thing on fire. We need you to answer this question! Sat Apr 13, 2013 12:26 am My Rhino is hitting the rev-limiter right at 32-34 mph. I'm thinking sticky reverse switch or maybe a short, any suggestions would be welcome. New iridium NGK plug, dynatek cdi and coil, fresh engine rebuild less than 2 … My rear brake light is on all the time on my 02 660. I was giving it some throttle when it started. My 02 grizzly reverse light stays on at all times no matter what gear I have it in. I was doing some clean up and checking fluids on my Grizzly 660 and I noticed the red reverse light blinking while I had the engine running in neutral. I have a 2006 Rhino 660 and the red reverse light on the dash panel lights solid red when in reverse gear like it it supposed to. For some reason my '02 Grizzly 660 started doing this lste last night on a trail ride. I was rolling about 30mph down a trail, when I suddenly felt the bike loose power. I have an 05 raptor 660r se that backfires and bogs really badly it kinda idles very not very well though and when I give it throttle it backfires badly and. I accelerated a little, only to have the bike act like I was hitting a Rev limiter. Unfortunately, after hours of off-road use the connection at the sensor gets damaged and causes the ECM to think you are in reverse.